UPVC Window Handle Replacement

Replacing a damaged or broken window glass replacement handle is a relatively simple process and, with the right tools, it can be done quite quickly. However, it is essential to know your handle's type and spindle's length prior to purchasing a replacement.

Older uPVC window handles have a spur that protrudes and locks over a cockspur wedge striker. They can be right-handed or left-handed and should match when replaced.

What kind of lock and handle do I have?

There are a myriad of upvc window locks and handles each with its particular advantages and uses. The kind of handle you choose will determine how easy it is to open your windows and UPVC Window Handle Replacement if the locking mechanism works as intended. As time passes, and with regular use the handles made of upvc on your windows could be damaged and worn out. This makes them less secure and less effective. In some instances, they could even fall off completely. It is essential to fix your window handles made of upvc immediately if you begin to notice them falling off. This will help to avoid burglaries and protect your home from burglary.

It's an easy task that virtually anyone can perform. With a few basic tools and the proper knowledge, this is a simple procedure that shouldn't take longer than a couple of minutes. You must know the type of handle or lock that you have on your window. This will help you choose the right replacement.

Inline Espagnolette Handles

These are the most commonly used type of upvc handle and are usually located on the other side of your window. They are flat and have an opening that engages the locking mechanism of the window frame. Inline upvc handles feature a spindle that runs through the middle of the handle and into the window frame to operate the latch.

Cockspur Handles

These handles are usually found on older uPVC window frames. They have distinct hook-shaped designs. Cockspur handles have a single screw that is used to secure the handle to the frame of the window and are not as secure as other types of window handles.

Handles that turn and tilt

The tilt and turn handles differ from other upvc handles because they can be turned to open the window and then tilted into the window to allow air circulation. Generally, they have a 7mm spindle on the back of the handle and are available in both left and right handed versions.

When purchasing replacement handles made of upvc It is crucial to measure the spindle's length since not all of them are the same size. Drop something into the middle of the hole to test the length. This is the length of the spindle that will fit your window.

What is the spindle?

uPVC window handles operate in a similar way as doors, with the user turning the handle to open an internal latch within the frame. The latch opens the window, so it can be closed and opened. The handles could be damaged, especially if they're often used or are subjected to harsh conditions. You may need to replace the handles on your uPVC window if they're not functioning properly.

There are several different types of uPVC handles to choose from, including Espag, Cockspur and Spaded handle options. These handles are made in a variety of ways to fit into uPVC frames. Each handle type uses a different spindle to lock the window mechanism. It is important to identify the type of handle installed on your uPVC windows so that you can replace it with the right one.

The base section of the handle will inform you what type of uPVC it is. A snap-in covers should be over the screw that holds the handle's base in place. Take it off and you should be able to see the second holding screw on the opposite side of the base of the handle. After both screws have been removed and you are able to pull the handle from the uPVC.

After removing the uPVC handle, remove it from the locking mechanism. Make note of the length of the spindle since you'll need to ensure that you purchase an alternative that is the same length as the original handle and locking mechanism.

The spindle wears down and cannot operate the locking mechanism. This can be due to damage from constant use or a loosening of the locking mechanism or even corrosion that occurs over time. When this happens it will be necessary to replace the window handle as well as the locking mechanism to restore full functionality to your uPVC windows.

How do I take off the handle that was previously attached?

In the course of time and daily use, window handles can become damaged or broken and if this happens, it is essential to fix them as soon as possible to ensure the security of your home. It is simple to replace a worn or damaged handle. The job can be accomplished in under an hour without the need of special tools.

The first step to remove the handle that was previously used is to take off the screw situated on the top of the handle base. Once the screw is removed, the handle will be pulled away. A second screw is situated at the base of the handle. It can also be removed. Once the two screws are removed, the handle can be detached from the base of the window.

Once the old handle has been removed, you can take the new handle and line up the fixing holes with the holes that are present in the window frame. There might be a small sticker or caps on the new handle, so remove these if necessary and then put the handle in place. Once the handle is in place it is essential to check that it works by turning the handle and making sure that the lock mechanism is activated.

Espag handles come with an extra spindle that is protruding from the handle and slot into a multipoint locking mechanism in the window frame. Cadenza windows come with an edge with cut-outs which slot into the lock mechanism, while Cockspur handles have an extended nose that hangs over the frame's outer or transom bar cross-member inside the window.

Once you have the new handle in place, insert the spindle inside the window lock and then tighten it down. Once the handle is securely fixed then replace the snap-in cover and the screw cap (if applicable). When the handle is ready to use, simply open and close the window a couple of times to make sure it is working properly and securely.

How do I put in the new handle?

Changing your uPVC window handle isn't difficult and the process is simple. All you need is a screwdriver, and a bit of patience. The first thing you need to do is ensure that the handle is in the unlocked position and then remove any screws that are visible. you can replace them by screw caps if you need. After removing the handle it is necessary to take an note of the length of the spindle that extends from the back of the handle. This is vital because it will determine the kind of handle you will need to purchase.

Espagnolette handles are the most common type of handle for uPVC windows. They have a spindle that is connected to the handle, and is responsible for an internal locking mechanism within the window frame. Once the handle is turned it opens the latch on the window and allows it to open. As time passes and with regular use, espagnolette handles may be damaged or destroyed and it is necessary to find a replacement.

Cadenza handles are a different kind of uPVC window handle, which is typically used on tilt and turn windows. They feature an extended blade that works a multipoint locking mechanism within the window. They are usually more secure than espagnolette handles since they can only be opened from the inside. They can be replaced with the same method as espagnolette handles however you should make sure that the new handle has an angled blade as opposed to flat ones.

After you have chosen the right handle, simply align the new handle with existing screw holes prior to screwing it in place. Then, put the screws on and test your new handle. This is done by shifting the handle from the locked to the unlocked position and vice versa a few times. If you experience any issues, it might be worth contacting a specialist to see if they are able to assist you in solving the issue. They can provide advice on how to fix the issue in a timely and effective way.