Peugeot 208 Key Replacement

It is best to delegate the replacement of Peugeot 208 keys to auto locksmiths that have the equipment and skills. They can create and program new keys much faster than a dealership would and at a cheaper cost.

A dead battery for your coin is most likely to blame if your key fob stops locking or unlocking the doors. There are other causes that the key might be malfunctioning.

Dead Coin Battery

A dead battery can stop your peugeot 207 key fob 208 from locking and unlocking, as well as stopping it from starting the engine. In this case you'll have to employ the alternate method of starting described in your vehicle owner's manual.

The spark plugs could also be worn out. The spark plugs ignite the fuel to start the engine. They are only able to last for a short time. If they are not used enough, they will eventually fail.

Luckily, there's an easy solution for this problem. Check the voltage of the battery with a multimeter. If the voltage is lower than 11,5 volts then it's time to replace it. If the battery has corrosion it is crucial to clean its contacts. You can do this by lifting the rubber covers covering the two terminals of the battery and using wire brushes to clean any parts that are corroded from the battery. Then, you must reconnect the positive pole cables to the negative.

Water Damage

If your 208 won't turn on and the battery is not flat, then you need to make sure whether the spark plugs work. You may find that they are simply too dirty and do not spark. The spark plugs can be cleaned in an workshop.

Peugeot automobiles use a key with a transponder compatible with the immobiliser. This ensures that only a valid key can turn the engine. If the chip inside the Peugeot key is damaged, it won't send the proper signal to the vehicle.

This is a frequent issue that is caused by water damage. This is a frequent issue in colder climates where the vehicle has been exposed to snow or rain. In this case, contact a trusted locksmith who will have the tools and equipment required to change the key's programming. They will also have all the latest technology and equipment needed to make the Peugeot smart key. The process should take no more than 15 minutes.

Faulty Battery Contacts

Peugeot replaced the old transponder chips by introducing a new model that utilizes electronic components mounted on a circuit board. The new system is effective when it's brand new, but as time passes, the circuit boards begin to deteriorate and stop working properly.

This can prevent the immobiliser chip from activating, so your car won't start. If this happens it's best to get in touch with a Peugeot specialist or locksmith.

A common issue is when the battery inside the key fob starts to fail. This causes the blade of the key to stop feeding into your lock. A locksmith in your car will replace the battery and cut a new blade for you. This is a simple fix.

Faulty Receiver Module

If your Peugeot key fob has stopped working after dropping it on the floor, or being exposed to a sudden rain or accidently washing it, it could be due a malfunctioning receiver module. The receiver module is responsible for transmitting radio frequency to the onboard computer that controls the central locking system of your Peugeot vehicle.

The key fob itself has rubber seals that block water from getting to the electronic chip inside. However prolonged exposure to water may penetrate these seals and damage the chip. The high salt content in the pool or ocean water could cause damage to the key fob if it is submerged.

If your Peugeot spare key fob isn't working You'll need the module replaced. This should be done by a Peugeot specialist or expert auto locksmith. Like other automobiles, Peugeot keys are protected by an exclusive immobilizer system that requires the correct coding for the start of the engine. This is the reason that you should only trust a peugeot partner key Fob Programming locksmith to design and program an alternative.

Faulty on-Board computer

The computer on board in your Peugeot is the one responsible for all of the systems inside your car, from power windows to airbags. The on-board computer will show the code when something goes wrong. This code will be stored in the system until the issue is fixed. In most cases, this will require replacing the onboard computer.

One of the main reasons for the light turning on is the loose or corroded connections within the airbag sensor. This could be due to wear and tear, age or exposure to salt and moisture. This issue must be taken care of as soon as you can, since an airbag malfunctioning could be dangerous in case in the event of an accident.

If your Peugeot is showing a card not detected error, the battery inside the key fob might be weak or dead. This will stop the key fob sending a signal that will disable your vehicle's immobilizer. You can test this by pressing the unlock button on the key fob, then trying to start your vehicle. If this doesn't work it is because the battery of the key needs to be replaced.